Call (480) 833-0901

Nissan

/Nissan

We Service and Repair Most Nissan Cars and Trucks

2006 Nissan Altima

2019-10-20T22:00:45+00:00

Nissan Altima

Mileage
175,976
Service Date
9/26/2019
Services Performed
  • Added about 1/2 gallon water to cooling system. Pressure tested cooling system. No leak detected at this time. Checked cooling fan operation. No fault. Connected scan tool. Multiple codes retrieved. P0725. Engine Speed Signal to TCM P0335. CKP Sensor circuit problem P0420. Catalyst Efficiency Low (B1) Turbine Sensor A/T 3rd Gear Function. Checked & inspected camshaft & crankshaft position sensor wirings and connections. No fault. Visually inspected and found sensor connector slightly oil soaked. Suggestions replace oil soaked cam & crank sensor. Clear DTC and reset computer. Road test for driveability concerns and recheck for turbine sensor and A/T 3rd gear function codes.
  • As a goodwill gesture to customer. Did not charge for replacing both camshaft and crankshaft position sensors. Performed warranty work. Original installed performed on 12/18/19 @ 268,807 . Invoice #1328
  • Did not duplicate overheating symptom as stated by customer. Possible sticking thermostat or clogged cooling system.
 
Elena T. gave our service a 5 star review on 10/18/2019
2006 Nissan Altima 2019-10-20T22:00:45+00:00

2006 Nissan Altima

2019-04-12T22:00:55+00:00

Nissan Altima

Mileage
171,304
Service Date
4/5/2019
Services Performed
  • Lube chassis (If applicable) Install new oil filter Change oil up to 5 qts. Perform 27 pt. inspection. See attached check-list Top off fluids underneath hood as needed. Set front and rear tire pressure to spec. Measure tire tread depth Test battery (if accessible) See attached print-out Reset oil life, service reminder, maintenance reminder, or service interval Wash front and rear exterior windows
 
Elena T. gave our service a 5 star review on 4/10/2019
2006 Nissan Altima 2019-04-12T22:00:55+00:00

2006 Nissan Altima

2019-02-21T23:00:22+00:00

Nissan Altima

Mileage
169,948
Service Date
2/5/2019
Services Performed
  • Lube chassis (If applicable) Install new oil filter Change oil up to 5 qts. Perform 27 pt. inspection. See attached check-list Top off fluids underneath hood as needed. Set front and rear tire pressure to spec. Measure tire tread depth Test battery (if accessible) See attached print-out Reset oil life, service reminder, maintenance reminder, or service interval Wash front and rear exterior windows
 
Elena T. gave our service a 5 star review on 2/19/2019
2006 Nissan Altima 2019-02-21T23:00:22+00:00

2016 Nissan Rogue

2018-03-14T22:00:32+00:00

Nissan Rogue

Mileage
31,318
Service Date
3/4/2018
Services Performed
  • Remove and resecure loose front bumper and install missing front left fog lamp hole cover.
 
Anessa B. gave our service a 5 star review on 3/13/2018
2016 Nissan Rogue 2018-03-14T22:00:32+00:00

2008 Nissan Rogue

2018-02-08T23:00:41+00:00

Nissan Rogue

Mileage
237,086
Service Date
2/3/2018
Services Performed
  • Lube chassis (If applicable) Install new oil filter Change oil up to 5 qts. Perform 27 pt. inspection. See attached check-list Top off fluids underneath hood as needed. Set front and rear tire pressure to spec. Measure tire tread depth Test battery (if accessible) See attached print-out Reset oil life, service reminder, maintenance reminder, or service interval Wash front and rear exterior windows
  • Road tested vehicle, and verified MIL is on and no drivability concerns. Connected scan tool and retrieved multiple codes in system.
  • Brake inspection
  • Measured front brake rotors. Current measurements: Front left brake rotor- .898 in. Front right brake rotor- .898 in. Normal thickness should be: 1.024 in. Minimum machining should be: .945 in. Discard at or under: NS Both front brake rotors below minimum machining spec.
  • Measured rear brake rotors. Current measurements: Rear left brake rotor- .559 in. Rear right brake rotor- .552 in. Normal thickness should be: .630 in, Minimum machining should be: .551 in. Discard at or under: NS Rear right brake rotor below minimum machining spec. Rear left brake rotor will be below minimum machining spec.
  • Torqued all wheels to spec. 80 ft. lb
 
Douglas B. gave our service a 5 star review on 2/7/2018
2008 Nissan Rogue 2018-02-08T23:00:41+00:00